How do I replace the 3rd cylinder on my 1996 Ford Contour? on 1996 Ford Contour


Answers :

You need a second opinion or clarification on your issue ? ask it in the comment box OR you can Ask Your Question

Tips for a great answer:

  • Please provide as much detail as possible as this will allow our members to better understand and respond to your Comment
  • If you need clarification, ask it in the comment box
  • It's 100% free, no registration required

Suggested Questions/Answers :

It is recommended you read all this kind of situations

This content reflects information from various individuals and organizations and may offer alternative or opposing points of view.

O-ring for #2 cylinder needs to b replaced on 1997 Ford Contour


I need an estimate for the replacement of an O-ring for the #2 cylinder. Want to be sure I don't get ripped off when it is replaced. Thank you for any information you can help me with. ...

Estimate to replace an O-ring for the #2 cylinder. on 1997 Ford Contour


Just bought the car took to advance auto they say needs repair on this O-ring. ...

1995 ford Contour grinds in 2nd and 3rd gear-manual transmission on 1995 Ford Contour


When I shift from 1st to 2nd and into 3rd gear I get grinding ...

What else could be wrong? I replaced front o2 sensor and misfire in cylinder 3 on 2004 Ford Focus SVT


replaced plug and cleaned Maf sensor checked air filter no black assume PCV is ok. Runs fine except at Idle. still sputters. Same codes and O2 and misfire 3rd cylinder. What else. ...

why is my #3 cylinder misfiring after replacement parts on 1999 Ford F-150


i replaced the plug, plug wire, and the coil pack and i still am getting a misfiring problem i have hooked it to the computer at the local shop and its stating it is the 3rd cylinder that is misfiring will someone help me i neeed to get this addresse ...

Does my transmission needs to be replaced? on 1999 Ford Contour


Okay so my dad got his first transmission fluid replaced at 150,000 miles... yes i know that was dumb but now it keeps slipping from out of overdrive into overdrive. Currently it wont shift into 3rd gear. I need to accelerate to get it going. The O/D ...

How to replace 1st cylinder coil on a 2003 Ford E350 XLT Super Duty Van? on 2003 Ford E-350


My van has a 1st cylinder misfire.It needs the coil replaced.I purchased the coil.I need instructions and helpful tips to install it myself please. Thank You! ...

I have a cylinder 2 and cylinder 5 misfire, replaced coil pack, wires and plugs. on 1997 Ford Explorer


The idle is rough, but smooths out and runs fine while driving. O2 sensors have been replaced also. ...

How easy or affordable is it to replace two cylinders? on 2002 Ford Escape


We paid a mechanic to replace the spark plugs & cylinders as well as the spark plug tube seals since oil was present around spark plug. He only replaced the plugs & let us drive off with two of them misfiring. We broke down on the freeway. No ...

how many hours does it take to replace master cylinder? on 1998 Ford Escort


To replace the master cylinder on a 1998 ford escort? ...

what causes the cylinders to need to be replaced? on 2002 Ford Thunderbird


Car has 25k miles and I just replaced all spark plugs as engine light was on. Engine light is back on and my mechanic says 2 cylinders need replacement and the other 6 will likely need replacement soon. ...

Do I need to replace a coil or a cylinder? How much would either cost? on 2002 Ford Escape


Think mechanic said cylinder had to be replaced after replacing spark plug does not remedy problem, but did he say coil? How much does it cost to repair coil? Cylinder? ...

estimate to replace cylinder head temp sensor & evaporate vent solenoid on 2002 Ford Mustang


Check engine diagnose found following DTC:P1285 cylinder head over temp condition (sensor). P1450 unable to bleed up fuel tank vacuum, P1299 cylinder head over temp protection active. Further test found cylinder head temp sensor reading up to 60 deg. ...

the fans wewe not working replaced them,replaced radiatior,waterpump,fuse, sens on 1995 Ford Contour


where should temp gauge read,says (normal) reads between a-l on gauge is this saying ity is to hot?and should my fan be running?it is winter here ...

how do you replace thermastat in a 2000 2.5 v contour on 2000 Ford Contour


over heats in just a few mins of cranking pictures would be great too im no machanic l.o.l ...

replaced master brake cylinder bled system still have no brake pressure. Why? on 2010 Ford Fusion


2010 Ford fusion s . Brake master cylinder was leaking I removed it and found that the main gasket had given out. I bought a brand new master cylinder and bled the system I still have no brake pressure . What could be wrong. There are no visible leak ...

how to replace the idler belt on 2000 Ford Contour


after replacing the thernastat i noticed idler belt was shredded.....how do replace it....... ...

Can a non mechanic replace the Cylinder Head Temperature Sensor? on 2003 Ford Expedition


I drove to the library (only 5 miles away). The check engine light came on and the temperature gauge pegged red. Two other warning lights came on: Reduced engine power & High Temperature/Low Oil. I got the codes pulled at Autozone. They read P129 ...

The #4 cylinder is not working-have replaced everything and need answer. on 2005 Ford Freestar


The wires, spark plugs and coil have all been replaced and the cylinder is still not working. Need to know what to do next. Getting diag code P0304. ...

How do I replace the clutch master cylinder and is It a difficult job? on 1999 Ford Escort


What tools are required for replacing the clutch master cylinder ...

A detailed question is important to get you a relevant answer .

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
all rights reserved to the respective owners || cheapestukipodrepairs.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2167 seconds